ACCESSORIES

PC 2.1 Cable for use with Labworldsoft. Image(s) are representative of the product group and not necessarily the individual product.

RH 5 Strap Clamp for securing vessels against walls or for synchronized rotation during stirring or dispersing. Includes boss head clamp R 270. For use with EUROSTAR Overhead Stirrers and ULTRA-TURRAX Dispersers.Image(s) are representative of the product...

• Cable 2 RS232• 9-pin male/female• Length: 3 metersImage(s) are representative of the product group and not necessarily the individual product.

Cable for connecting equipment to PC. Length: 3 meters.Image(s) are representative of the product group and not necessarily the individual product.

Cable for connecting equipment to PC. Length: 2.5 meters.Image(s) are representative of the product group and not necessarily the individual product.

Shaft and impeller blades to fit collet of BDC250 stirrer (Cat. No. 340-98077). Made of all elctropolished 316L stainless steel. Includes one radial blade and one axial blade and interchangeable screw set. This set is also included in the BDC250 stirrer...

These stainless steel blade stirrer generate a radial flow. For drawing the material to be mixed from the top and bottom. For aerating of low viscosity media and for homogenizing solids in liquids. Used at medium to high speeds.Image(s) are...

These stainless steel spiral stirrers generate axial flow. Medium is conveyed from the bottom upwards. For homogeneous mixing and heat exchange of medium to high viscosity media. Used at low to medium speeds.Image(s) are representative of the product...

Stainless steel support rod for all magnetic stirrers with M 10 threaded bushing. • Diameter: 10 mm • Length: 450 mm • Material: stainless steel (AISI 304)Image(s) are representative of the product group and not necessarily the...

For fastening a temperature sensor or ETS-D5/6 (Cat. No. 330-99085 / 330-99088) with a boss head H 44 (Cat. No. 330-29152) to the support rod H 16 V (Cat. No. 330-23068).Image(s) are representative of the product group and not necessarily the individual...

• For fastening the holding rod H 38 to the support rod H 16 V• Cast aluminum• For stand diameters: 10 to 11 mm• For extension arm diameter: 11 mm• Max. length of extension arm: 200 mm• Max. load: 1 kg• Max...

For attaching the safety switch SI 400 (Catalog No. 140-99596) to the telescopic stand R 474 (Cat. No. 340-98536) and R 653 (Cat. No. 330-23422).Image(s) are representative of the product group and not necessarily the individual product.

To attach the safety switch SI 400 (Cat. No. 140-99596) to the floor stand R 472 (Cat. No. 340-98533).Image(s) are representative of the product group and not necessarily the individual product.

The SI 400 consists of an end switch (normally closed contact / switch) and a magnetic switch contact (actuator) which is mounted on the floor stand R 472 (Cat. No. 340-98533) with the fixing device SI 472 (Cat. No. 140-99599) and on the telescopic stand...

Cast aluminum Boss Head Clamp for T25 and T18 Digital ULTRA-TURRAX Dispersers and EUROSTAR 20 and 40 Overhead Stirrers• For stand diameters: 6 to 16 mm• For extension arm diameters: 6 to 16 mm• Max. length of extension arm: 300...

Keypad attaches to the front of MultiMagStir Genie (Cat. No. 360-77642). Thread the cable through the slot in plastic housing. Peel and Stick Adhesive back adheres keypad easily to housing. Then connect the ribbon cable.Image(s) are representative of the...

Insulating Mat prevents heating of sample. Replacement part for MagStir Genie (Cat. No. 360-10200) and MultiMagStir Genie (Cat. No. 360-77642). Image(s) are representative of the product group and not necessarily the individual product.

Keypad attaches to the front of MagStir Genie (Cat. No. 360-10200). Thread the cable through the slot in plastic housing. Peel and Stick Adhesive back adheres keypad easily to housing. Then connect the ribbon cable.Image(s) are representative of the...

LCD Display Board for all voltages of the MagStir Genie (Cat. No. 360-10200) and MultiMagStir Genie (Cat. No. 360-77642).Image(s) are representative of the product group and not necessarily the individual product.

Power Supply used on all voltages of MagStir Genie (Cat. No. 360-10200) and MultiMagStir Genie (Cat. No. 360-77642).Image(s) are representative of the product group and not necessarily the individual product.

Power Cord for 120V and 100V. Simply plug into Power Supply (Cat. No. 360-77969). Replacement part for MagStir Genie (Cat. No. 360-10200) and MultiMagStir Genie (Cat. No. 360-77642).Image(s) are representative of the product group and not necessarily the...

Silicone Mat prevents containers from vibrating off the unit at high speeds. For use with QuadMag Genie Magnetic Stirrers (Catalog No. 360-77657 and 430-97858).Image(s) are representative of the product group and not necessarily the individual product.

This is the belt between the motor pulley and four the magnet pulleys. Replacement part for QuadMag Genie (Cat. No. 360-77657) and Digital QuadMag Genie (Cat. No. 430-97858).Image(s) are representative of the product group and not necessarily the...

Four adhesive mounted feet. Replacement part for RotoShake Genie (Cat. No. 360-10191), Rotator Genie (Cat. No. 360-78040 and 360-78043), MegaMag Genie (Cat. No. 360-77651 and 330-77654), MultiMagStir Genie (Cat. No. 360-77642), and QuadMag Genie (Cat. No...

The Digital Keypad is used on the 120V, 230V and 100V Digital MegaMag Genie magnetic stirrer. Thread the cable through the slot in housing. Peel and Stick Adhesive back adheres keypad easily to casting. Then connect the ribbon cable.Image(s) are...

The Digital Timer Board is used on the 120V, 230V and 100V Digital MegaMag Genie magnetic stirrer, and can be easily installed. Attaches with four mounting screws from inside of the unit.Image(s) are representative of the product group and not...

Magnet assembly includes magnets, plate and pulley. Replacement part for the MegaMag Genie (Catalog No. 360-77651 and 360-77654).Image(s) are representative of the product group and not necessarily the individual product.

This is the belt between the motor pulley and the magnet pulley of the MegaMag Genie (Catalog No. 360-77651 and 360-77654).Image(s) are representative of the product group and not necessarily the individual product.

These System Stands have been adapted to support additional apparatus for process monitoring and chemical synthesis. The base accommodates a central 25 mm (1 in.) diameter stand rod, and up to two additional 16 mm (5/8 in.) diameter Accessory Rods (Cat...

3/8 in. (9.5 mm) diameter shafts with a turned down 1/2 x 5/16 in. (13 x 8 mm) end. Will accommodate blades with both 5/16 and 3/8 diameters. All shafts are made from passivated 316L stainless steel for maximum corrosion protection. Image(s) are...

Dispersion blade composed of chemically inert and corrosion resistant electropolished 316L stainless steel. Broken particles are dispersed by the laminar flow set up by the blade. The 5/16 in. (8 mm) bore is compatible with all Caframo shafts. Set screws...

Straight blade composed of chemically inert and corrosion resistant electropolished 316L stainless steel. The 5/16 in. (8 mm) bore is compatible with all Caframo shafts. Set screws included. For high shear, low viscosity mixing with moderate vortexing,...

Pitched blade propeller composed of chemically inert and corrosion resistant electropolished 316L stainless steel. The 5/16 in. (8 mm) bore is compatible with all Caframo shafts. Set screws included. For low shear, high top-to-bottom pumping capacity...

2 in. (50 mm) radial flow turbine 3-blade propellers. Composed of chemically inert and corrosion resistant electropolished 316L stainless steel. Set screws included. For high shear mixing with moderate vortexing.• Cat. No. 340-98101 is compatible...

2 in. (50 mm) pitched blade propellers composed of chemically inert and corrosion resistant electropolished 316L stainless steel. Set screws included. For low shear, high top-to-bottom pumping capacity with high gas injection.Specifications:• Flow...

Pitched blade propeller composed of chemically inert and corrosion resistant electropolished 316L stainless steel. The 5/16 in. (8 mm) bore is compatible with all Caframo shafts. Set screws included. For low shear, high top-to-bottom pumping capacity...

Pitched blade propeller composed of chemically inert and corrosion resistant electropolished 316L stainless steel. The 5/16 in. (8 mm) bore is compatible with all Caframo shafts. Set screws included. For low shear, high top-to-bottom pumping capacity...

An axial flow PTFE impeller for high speed, low viscosity mixing. With 45° pitched blades, the impeller is attached to a PTFE-coated stainless steel core shaft. The stainless steel core of the shaft provides stability. PTFE (polytetrafluoroethylene)...

A tangential flow PTFE impeller for low speed, higher viscosity mixing. The blade is attached to a PTFE-coated stainless steel core shaft. Designed for use in round bottom vessels and reaction flasks. The stainless steel core of the shaft provides...

A radial flow PTFE impeller for high speed, low viscosity mixing in narrow neck flasks. The blades are attached to PTFE-coated shaft, fanning out with agitation to a maximum diameter of 11/2 in. (40 mm). The stainless steel core of the shaft provides...