CONNECTING

For determining water content in petroleum or bituminous products, graduated upwards from the stopcock to 3 ml in 0.2 ml divisions, and from 3 ml to 20 ml in 0.5 ml divisons.Image(s) are representative of the product group and not necessarily the...

The 10 ml receiver is graduated from 0 to 1 ml in 0.1 ml intervals, with a maxium scale error of 0.05 ml. The graduation intervals from 1.0 to 10 ml are 0.2 ml, with a maximum scale error of 0.1 ml.Image(s) are representative of the product group and not...

With an outer TS joint at the top and a larger inner † joint at the bottom.Image(s) are representative of the product group and not necessarily the individual product.TS Joint Size Top Outer: 10/30TS Joint Size Bottom Inner: 19/38Approx. Length...

Apparatus for maintaining oxygen-free solvents. Head has sufficient storage space to allow solvent removal by syringe or drainage through 2 mm T-bore PTFE stopcock. With TS 24/40 outer joint at top, TS 24/40 inner joint at bottom and TS 14/20 inner joint...

Connecting 75 degree distillation adapters. For use as a component in atmospheric or vacuum distillations. Lower and sidearm joints are inner Standard Taper joints; upper joint is outer Standard Taper joint. Joints are same size. Manufactured from 33...

Used in distillation assemblies where adjustable immersion depth of the thermometer is desired. Threaded top BEVEL-SEAL™ connection for plain stem thermometers. Vacuum-tight seal is achieved with the open top compression cap and FKM o-ring...

Useful in the sub-boiling separation of mixtures having volatile components. Vacuum connection at side accepts 1/4 in. I.D. flexible tubing. Sealed-in drip tip directs condensate. Standard Taper inner joints are parallel. Joints are the same size...

Designed for purification and transfer of solvents under airless conditions. Incorporates a HI-VAC® valve with an 826601-0004 plug. Standard Taper inner joints are parallel. Lower joints are the same size. Manufactured from 33 expansion, low...

Useful in the sub-boiling separation of mixtures having volatile components. Standard Taper inner joints are parallel. Joints are the same size. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438,...

Rubber Adapters, 1/4 in. hole in the top for use with plain stem thermometers, gas inlet tubes, etc. Replacement parts for Thermometer Inlet Adapter with Top Tubulature (Cat. No. 985-16114, 985-16117, and 985-13168).Image(s) are representative of the...

• Standard Taper joint at the bottom and a tubulature at the top• Includes a rubber adapter with a 1/4 in. hole in the top for use with plain stem thermometers, gas inlet tubes, etc.• Manufactured from 33 expansion, low extractable...

Hose connection provides a gas inlet for reactions. Allows access to the bottom of flasks/tubes. User may shorten the lower tube to fit the flask or apparatus. #2 hose connection. Tube length 200 mm. Approximate overall height 355 mm.Image(s) are...

With hose connection for a vacuum or the introduction of gases. For use with plain thermometers, pipets, syringes or other small instruments with an OD from 2 to 17 mm. A vacuum-tight seal is effected with the compression cap and Viton O-ring to allow...

TS inner joint to GPI thread.Image(s) are representative of the product group and not necessarily the individual product.GPI Thread Size: 20-400TS Joint: 14/20Overall Dimensions (in.): 50GPI Thread Size: 20-400TS Joint: 19/22Overall Dimensions (in.): 55

This connecting adapter allows interfacing of Standard Taper ground jointed glassware with threaded microscale components. Accessory for microscale MICROFLEX threaded kits. Connects Standard Taper outer ground joint to GPI thread of inner ground joint...